RAD Data comm 100 Spécifications Page 250
- Page / 318
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7 Application Tutorial Installation and Operation Manual
7-6 User and Management Traffic Separated by VLAN Egate-100 Ver. 4.0
CONTROL
Egate-100
RDY
ALM
12
LIN K
MNG-ETH
LIN K
ACT
GbE
ACT
1 2
STM-1/OC-3STM-1/OC -3
LINK
SYNCSYNC
DCE
Figure
7-7: CONTROL Connector
Connecting to the Network Management Station
Egate-100 is connected to an NMS via an 8-pin RJ-45 connector designated
MNG ETH. Refer to
Appendix A
for the connector pinout.
³ To connect to an NMS:
• Connect Egate-100 to a hub or switch using a straight cable
Or;
• Connect Egate-100 to a network interface card using a cross cable.
When connecting Fast Ethernet cables longer than 30 meters (98 feet), it is
recommended to use shielded cables.
CONTROL
Egate-100
RDY
ALM
12
LIN K
MNG-ETH
LIN K
ACT
GbE
ACT
1 2
STM-1/OC-3STM-1/OC -3
LINK
SYNCSYNC
DCE
Figure
7-8: Fast Ethernet Management Connector
Connecting to Power
Egate-100 can be ordered with either AC power or DC power (single or dual
power supply).
Connecting to AC Power
AC power is supplied to Egate-100 via a standard 3-prong plug.
AC power should be supplied through the 1.5m (5 ft) standard power cable
terminated by a 3-prong plug. The cable is provided with the unit.
Note
- Egate-100 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Declaration of Conformity 13
- Glossary 14
- Quick Start Guide 21
- Configuring Basic Parameters 22
- Quick Setup Menu 23
- Contents 27
- Egate-100 Ver. 4.0B iii 29
- Egate-100 Ver. 4.0B v 31
- Chapter 1 33
- Introduction 33
- Features 35
- Classification 37
- Web-based Management 38
- Security 38
- 1.2 Physical Description 39
- 1.3 Functional Description 39
- STM-1 Mapping 41
- SONET Mapping 42
- VLAN-Aware Mode 43
- Ingress Process 44
- Learning Process 45
- Aging Process 45
- Forwarding Process 46
- Egress Process 46
- VLAN-Unaware Mode 47
- Queue Management 50
- Quality of Service 50
- IP Precedence / DSCP 51
- VLAN Priority 51
- Encapsulation 52
- TX Traffic Path 53
- RX Traffic Path 55
- Statistics 56
- Multilink PPP 57
- Management Access 59
- Statistics Collection 61
- Configuration Reset 61
- Chapter 2 67
- Installation and Setup 67
- 2.4 Mounting the Unit 69
- 2.10 Connecting to Power 73
- Chapter 3 75
- Operation 75
- Working with Terminal 79
- Logging In 81
- Principles of Navigation 83
- Hot Keys 83
- Menu Maps 85
- 3.6 Turning Off the Unit 91
- Chapter 4 93
- Configuration 93
- 4-3. Ethernet Traffic Flow 97
- Egate-100 Ver. 4.0 100
- Defining Host Parameters 101
- Configuring SNMPv3 103
- Adding SNMPv3 Users 105
- Assigning Traps 107
- Configuring Target Address 109
- Entering Device Information 111
- Configuring User Access 113
- Configuring Network Managers 115
- 4-22. Radius Parameters 117
- 4-8. Radius Parameters 117
- Configuring the Clock Source 119
- Configuring Protection 121
- FE-UAS – 133
- VCAT support, which is 153
- Configuring the Bridge 155
- Configuring the MAC Table 157
- Configuring the Bridge Ports 157
- Defining Policer Profiles 168
- Defining Shaper Profiles 170
- Defining Queue Profiles 171
- Defining Flows 174
- Viewing SNTP Status 179
- Viewing APS Status 181
- Viewing STM-1/OC-3 Status 184
- Viewing Logical Port Status 189
- Displaying Flow Information 196
- 4-122. View Flow Screen 197
- 4-42. View Flow Parameters 197
- Viewing Inventory 199
- Save your changes 201
- Resetting Egate-100 203
- Chapter 5 205
- Monitoring and 205
- Diagnostics 205
- Viewing Radius Statistics 215
- Alarms and Events 217
- 5-8. System Events List 219
- 5-10. SOH Alarms List 221
- VC Alarms List 221
- Displaying Alarms 229
- Running BERT Test 233
- Viewing Self Test Results 233
- Chapter 6 235
- Software Upgrade 235
- 6.2 Impact 236
- 6.4 Prerequisites 236
- Utilities Menu 237
- Accessing the Boot Menu 240
- 6-10. File Menu 242
- Caution 243
- Chapter 7 245
- Application Tutorial 245
- Mounting the Unit 247
- Connecting to the Terminal 249
- Connecting to AC Power 250
- Connecting to DC Power 251
- Setting SDH/SONET Parameters 253
- Viewing Bridge Statistics 265
- Installing Egate-100 267
- Setting Ethernet Parameters 273
- Running Diagnostic Tests 281
- Equipment List 283
- Setting System Parameters 289
- Configuring T3 and T1 ports 291
- 7-87. Diagnostics Menu 305
- Appendix A 307
- Connection Data 307
- Appendix B 309
- SDH/SONET Mapping 309
- AC/DC Adapter 311
- (AD) Plug 311
- AC/DC Adapter (AD) Plug 312
- Customer Response Form 313
- Error Report 315
- The Access Company 318
Produits connexes et manuels pour Mise en réseau RAD Data comm 100
(106 pages)
Mise en réseau RAD Data comm T1 Spécifications
(158 pages)
(158 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels