RAD Data comm 100 Spécifications Page 18
- Page / 318
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Node
A point of interconnection to a network.
Packet
An ordered group of data and control signals transmitted through
a network, as a subset of a larger message.
parameters
Parameters are often called arguments, and the two words are
used interchangeably. However, some computer languages such as
C define argument to mean actual parameter (i.e., the value), and
parameter to mean formal parameter. In RAD CLI, parameter
means formal parameter, not value.
Payload
The 48-byte segment of the ATM cell containing user data. Any
adaptation of user data via the AAL will take place within the
payload.
Physical Layer
Layer 1 of the OSI model. The layer concerned with electrical,
mechanical, and handshaking procedures over the interface
connecting a device to the transmission medium.
Port
The physical interface to a computer or multiplexer, for connection
of terminals and modems.
prompt
One or more characters in a command line interface to indicate
that the computer is ready to accept typed input.
Protocol
A formal set of conventions governing the formatting and relative
timing of message exchange between two communicating
systems.
QoS (Quality of Service)
Refers to the capability of a network to provide better service to
selected network traffic over various technologies, including Frame
Relay, Asynchronous Transfer Mode (ATM), Ethernet and 802.1
networks.
Router
An interconnection device that connects individual LANs. Unlike
bridges, which logically connect at OSI Layer 2, routers provide
logical paths at OSI Layer 3. Like bridges, remote sites can be
connected using routers over dedicated or switched lines to create
WANs.
Serial Transmission
A common mode of transmission, where the character bits are
sent sequentially one at a time instead of in parallel.
Single Mode
Describing an optical wave-guide or fiber that is designed to
propagate light of only a single wavelength (typically 5-10 microns
in diameter).
Space
In telecommunications, the absence of a signal. Equivalent to a
binary 0.
Sync
See Synchronous Transmission.
Synchronous
Transmission
Transmission in which data bits are sent at a fixed rate, with the
transmitter and receiver synchronized.
- Egate-100 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Declaration of Conformity 13
- Glossary 14
- Quick Start Guide 21
- Configuring Basic Parameters 22
- Quick Setup Menu 23
- Contents 27
- Egate-100 Ver. 4.0B iii 29
- Egate-100 Ver. 4.0B v 31
- Chapter 1 33
- Introduction 33
- Features 35
- Classification 37
- Web-based Management 38
- Security 38
- 1.2 Physical Description 39
- 1.3 Functional Description 39
- STM-1 Mapping 41
- SONET Mapping 42
- VLAN-Aware Mode 43
- Ingress Process 44
- Learning Process 45
- Aging Process 45
- Forwarding Process 46
- Egress Process 46
- VLAN-Unaware Mode 47
- Queue Management 50
- Quality of Service 50
- IP Precedence / DSCP 51
- VLAN Priority 51
- Encapsulation 52
- TX Traffic Path 53
- RX Traffic Path 55
- Statistics 56
- Multilink PPP 57
- Management Access 59
- Statistics Collection 61
- Configuration Reset 61
- Chapter 2 67
- Installation and Setup 67
- 2.4 Mounting the Unit 69
- 2.10 Connecting to Power 73
- Chapter 3 75
- Operation 75
- Working with Terminal 79
- Logging In 81
- Principles of Navigation 83
- Hot Keys 83
- Menu Maps 85
- 3.6 Turning Off the Unit 91
- Chapter 4 93
- Configuration 93
- 4-3. Ethernet Traffic Flow 97
- Egate-100 Ver. 4.0 100
- Defining Host Parameters 101
- Configuring SNMPv3 103
- Adding SNMPv3 Users 105
- Assigning Traps 107
- Configuring Target Address 109
- Entering Device Information 111
- Configuring User Access 113
- Configuring Network Managers 115
- 4-22. Radius Parameters 117
- 4-8. Radius Parameters 117
- Configuring the Clock Source 119
- Configuring Protection 121
- FE-UAS – 133
- VCAT support, which is 153
- Configuring the Bridge 155
- Configuring the MAC Table 157
- Configuring the Bridge Ports 157
- Defining Policer Profiles 168
- Defining Shaper Profiles 170
- Defining Queue Profiles 171
- Defining Flows 174
- Viewing SNTP Status 179
- Viewing APS Status 181
- Viewing STM-1/OC-3 Status 184
- Viewing Logical Port Status 189
- Displaying Flow Information 196
- 4-122. View Flow Screen 197
- 4-42. View Flow Parameters 197
- Viewing Inventory 199
- Save your changes 201
- Resetting Egate-100 203
- Chapter 5 205
- Monitoring and 205
- Diagnostics 205
- Viewing Radius Statistics 215
- Alarms and Events 217
- 5-8. System Events List 219
- 5-10. SOH Alarms List 221
- VC Alarms List 221
- Displaying Alarms 229
- Running BERT Test 233
- Viewing Self Test Results 233
- Chapter 6 235
- Software Upgrade 235
- 6.2 Impact 236
- 6.4 Prerequisites 236
- Utilities Menu 237
- Accessing the Boot Menu 240
- 6-10. File Menu 242
- Caution 243
- Chapter 7 245
- Application Tutorial 245
- Mounting the Unit 247
- Connecting to the Terminal 249
- Connecting to AC Power 250
- Connecting to DC Power 251
- Setting SDH/SONET Parameters 253
- Viewing Bridge Statistics 265
- Installing Egate-100 267
- Setting Ethernet Parameters 273
- Running Diagnostic Tests 281
- Equipment List 283
- Setting System Parameters 289
- Configuring T3 and T1 ports 291
- 7-87. Diagnostics Menu 305
- Appendix A 307
- Connection Data 307
- Appendix B 309
- SDH/SONET Mapping 309
- AC/DC Adapter 311
- (AD) Plug 311
- AC/DC Adapter (AD) Plug 312
- Customer Response Form 313
- Error Report 315
- The Access Company 318
Produits connexes et manuels pour Mise en réseau RAD Data comm 100
(106 pages)
Mise en réseau RAD Data comm T1 Spécifications
(158 pages)
(158 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels