RAD Data comm ASMi-52L Spécifications Page 162
- Page / 184
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7 Application Tutorial Installation and Operation Manual
7-6 Equipment List ASMi-52 Ver. 2.5
LRS-16
Configuration>System>Management>Host
1. IP Address … (0.0.0.0)
2. Mask … (255.255.255.0)
3. Default gateway … (0.0.0.0)
4. Read community … (public)
5. Write community … (private)
6. Trap community … (public)
>
ESC-Previous menu; !-Main menu; &-Exit 1M/ 1C
Figure
7-8. Host Screen
2. Enter the following parameters (for example):
• IP address – 172.17.152.131
• IP mask – 255.255.255.0
• Default gateway – 172.17.152.1
3. Press <S> to save the parameters.
The changes are saved in the unit.
Configuring the Network Managers
The network management stations to which the SNMP agent sends traps can be
defined or modified. Up to ten managers can be defined. Entering the IP address
and corresponding subnet mask defines each management station. In addition,
you can temporarily prevent a manager station from receiving traps by masking
the network manager.
³ To edit the manager list:
1. Select Main Menu> Configuration> System> Management> Managers list.
The Management List screen appears.
- 2/4-Wire SHDSL Modem 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Caution 8
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Declaration of Conformity 13
- Glossary 15
- Quick Start Guide 21
- Configuring the Master Clock 22
- Configuring the T1 Interface 23
- Contents 25
- ASMi-52 Ver. 2.8 iii 27
- Chapter 1 29
- Introduction 29
- ASMi-52 Ver. 2.8 30
- DTE Interface 33
- DTE+LAN 36
- Dial-In 37
- Dial-Out 37
- 1.3 Functional Description 39
- ASMi-52 Ver. 2.8 40
- Chapter 2 45
- Installation and Setup 45
- Connecting to DTE Equipment 49
- ³ To connect DC power: 51
- Chapter 3 53
- Operation 53
- Rear Panel Indicators 55
- 3.3 Default Settings 56
- Working with Terminal 60
- Choosing Options 61
- Working with Web Terminal 62
- Working with ConfiguRAD 63
- Working with RADview 64
- Working with SNMP 64
- Menu Map 65
- 3.5 Turning Off ASMi-52 68
- Chapter 4 69
- Configuration 69
- Entering Device Information 70
- Selecting the CTS State 76
- Selecting the DSR State 76
- Timeout 78
- Appendix A 79
- Local Card Mode 83
- Remote Card Mode 83
- Configuring the Snext Margin 86
- Configuring Line Probing 88
- Configuring the E1 Interface 90
- Selecting E1 Framing Mode 92
- Setting the Sync Mode 93
- Defining Idle Code 94
- Mapping E1 Timeslots 94
- Configuring the LAN Port 99
- Configuring Aging Timeout 101
- Configuring QoS Mapping 101
- Setting the LAN Rate 102
- Configuring Autonegotiation 104
- Detecting SHDSL Link Failure 104
- Displaying the System Status 105
- Displaying the Port Status 106
- Accessing the Remote ASMi-52 107
- 4-41. Inventory Screen 108
- ASMi-52 110
- Main menu 110
- ConfiguRAD 110
- 4-46. TFTP Menu 111
- Switching Software Versions 114
- Resetting ASMi-52 115
- Resetting the ASMi-52 Modem 116
- Resetting the SHDSL Repeater 117
- 4-52. Repeater Reset Menu 118
- Chapter 5 119
- Monitoring and 119
- Diagnostics 119
- Displaying E1/T1 Statistics 122
- 5.2 Detecting Errors 126
- 5.3 Handling Events 126
- Displaying All Alarms 127
- Masking Port Alarms 129
- 5-4. ASMi-52 Events 132
- 5-15. Port Log File Screen 133
- Handling Traps 134
- 5.4 Troubleshooting 135
- Running Loopback Tests 138
- Running the Local Loopback 139
- Running the Remote Loopback 141
- Deactivating the Loopbacks 142
- Running the LEDs Test 143
- 5.7 Technical Support 146
- Chapter 6 147
- Software Upgrade 147
- 6.4 Prerequisites 148
- Utilities Menu 148
- Activating the TFTP Server 150
- 6-4. TFTP Menu 151
- Using the XMODEM Protocol 153
- 6-6. Boot Manager Menu 154
- Using the TFTP 155
- Chapter 7 157
- Application Tutorial 157
- Installing LRS-16 158
- Copper Cable 160
- Station Clock Port 160
- Configuring the Host IP 161
- 7-8. Host Screen 162
- Setting Management Access 163
- Configuring the E1 Port 165
- 7-16. Station Clock Screen 167
- Chapter 4 167
- Running Diagnostic Tests 168
- 7-19. Local Tests Screen 169
- Displaying Alarms 170
- Event Reporting 172
- Appendix A 173
- Connection Data 173
- A.2 SHDSL Interface 175
- A.3 CONTROL Connector 176
- A.4 Alarm Relay Connector 177
- A-2. ALARM Pin Functions 178
- Customer Response Form 179
- Error Report 181
- The Access Company 184
Produits connexes et manuels pour Mise en réseau RAD Data comm ASMi-52L
Mise en réseau RAD Data comm 100 Spécifications
(318 pages)
(318 pages)
(106 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels