RAD Data comm Optimux-34 Spécifications Page 104
- Page / 118
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 6 Software Upgrade Installation and Operation Manual
6-8 Upgrading Optimux-34 Software via the Boot Menu Optimux-34 Ver. 2.81
³ To download software release via XMODEM:
1. From the Boot menu, select Download an Application by XMODEM. You will
see a message that requests the partition number to which the new software
is to be downloaded, and offers a recommended value.
2. If there is no special reason to select a different value, type the
recommended number and then press <Enter>. A typical display is shown
below:
Select Copy number for download ( 1 )
Select: 1
3. The process starts, and you will see:
Erasing Partition please wait ....
Please start the XMODEM download.
4. Start the transfer in accordance with the program you are using. For example,
if you are using the Windows HyperTerminal utility:
Select Transfer in the HyperTerminal menu bar, and then select Send File
on the Transfer menu.
The Send File window is displayed:
Select the prescribed Optimux-34 software file name (you may use
the Browse function to find it).
In the Protocol field, select XMODEM.
When ready, press Send in the Send File window. You can now monitor
the progress of the downloading in the Send File window.
If downloading fails, repeat the whole procedure.
5. When the downloading process is successfully completed, you will see a
sequence of messages similar to the following:
Loading ...
Decompressing to RAM.
Processing archive: FLASH
Extracting OPTIMUX.BIN
..........................................................
.................................................................... CRC OK
Running ...
*******************************************************************
* In order to start working - press the ENTER button for few times*
*******************************************************************
6. At this stage, press the <Enter> key several times to go to the log in screen.
Note
- Optimux-34 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- 3. Configuring Optimux-34 18
- Selecting the Clock Source 19
- Contents 21
- Optimux-34 Ver. 2.81 iii 23
- Chapter 1 25
- Introduction 25
- Point-to-Point Application 26
- Wireless Link Application 27
- Application 28
- 1.2 Physical Description 29
- 1.3 Functional Description 30
- Power Supply Redundancy 31
- Link Redundancy 31
- Management Requirements 32
- Clocking 32
- Power Requirements 33
- Optimux-34 Ver. 2.81 34
- Chapter 2 37
- Installation and Setup 37
- 2.3 Required Equipment 38
- 2.4 Mounting the Unit 38
- Appendix A 40
- Warning 40
- Caution 40
- Connecting to E3 Link 41
- Connecting to Alarm Relay 42
- 2.7 Connecting to Power 43
- Chapter 3 45
- Operation 45
- 3.3 Default Settings 48
- RADview-TDM 50
- User's Manual 50
- Chapter 4 50
- Starting a Control Session 51
- Choosing Options 51
- Correcting Entries 52
- Navigating Data Forms 52
- Web Browser Requirements 54
- Working with RADview 55
- 3.5 Menu Map 56
- 3.6 Turning Off Optimux-34 57
- Chapter 4 59
- Configuration 59
- Chapter 1 60
- Setting up the Manager List 64
- Management Access 65
- Configuring the Control Port 66
- Configuring Security Timeout 68
- Setting the Alarms 68
- Configuring the E3 Port 72
- Configuring the E1 Port 73
- Configuring the V.35 Port 74
- 4-19. Change Access Menu 76
- 4-20. User Info Menu 77
- 4-21. Factory Default Menu 77
- Viewing the Inventory 78
- RAD Technical Support 81
- Chapter 6 81
- Downloading the License File 81
- Activating the License File 82
- Chapter 5 85
- Monitoring and 85
- Diagnostics 85
- Event Log 86
- System Status 87
- Interface Status 88
- 5.2 Detecting Errors 90
- Loop Connections 91
- 5.5 Technical Support 96
- Chapter 6 97
- Software Upgrade 97
- 6.4 Prerequisites 98
- Utilities Menu 98
- Activating the TFTP Server 99
- 6-2. TFTP Menu 100
- 6-1. TFTP Values 101
- Using the XMODEM Protocol 103
- Using the TFTP 105
- Appendix A 107
- Pinouts 107
- Optimux-34 Ver. 2.81 108
- A.3 Alarm Connector 109
- A.4 Control Connector 110
- A.5 Power Connectors 110
- A.6 V.35 Connectors 110
- A-5. V.35/ISO-2110 Pinout 111
- A-6. V.35/Telebras Pinout 112
- Customer Response Form 113
- Error Report 115
- The Access Company 118
Produits connexes et manuels pour Mise en réseau RAD Data comm Optimux-34
(114 pages)
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels