RAD Data comm E1 Interface Converter RIC-E1 Spécifications Page 83
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module
Diagnostic Tool (Ping Terminal) Menu D-29
Using the Ping Function
The Ping option is used to confirm IP connectivity by pinging other IP hosts.
Connectivity is confirmed by receiving a reply from the remote (pinged) IP host.
To ping a host:
1. From the Diagnostic Tools menu, type 1 and enter the desired host IP address.
2. Press <Enter> to confirm the destination IP address.
3. To start pinging, type 2 on the Diagnostic Tools screen.
After pinging starts, you can monitor the ping status. A typical screen is
shown in Figure D-29.
After pinging is started, it continues in the background even if you exit the
Diagnostics Tools screen. In this case, a Ping Running message appears in the top
upper left-hand corner of the screen.
4. To stop pinging, type 3 from the Diagnostic Tools menu.
A Ping Stopped message is displayed.
To clear the message and return to the Diagnostic Tools screen, press any
key.
IR_IP <IR-IP> S/W Ver. 1.21 31/IR (date)
Quick Setup
Management Access
Advanced Setup
Device Control
View
Diagnostic Tools (PING terminal)
=====================================================================
1. Ping IP Address :192.168.100.011
2. Start Pinging :>>>
3. Stop Pinging :>>>
Pinging 192.168.212.001 Sent 27 Recvd 25 Lost 2 Resp.Time 60 ms
Press one of the numbers to select or ESC:
Figure D-29. Diagnostic Tools Menu after Receiving Pinging Response
Note
- E1 Interface Converter 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating RIC-E1 12
- Contents 13
- List of Figures 14
- List of Tables 14
- Chapter 1 15
- Introduction 15
- 1.2 Physical Description 16
- 1.3 Functional Description 17
- 1.4 Technical Specifications 18
- Chapter 2 21
- Installation and Setup 21
- 2.3 Configuring RIC-E1 22
- Configuring RIC-E1 2-3 23
- Connecting the Interfaces 24
- Connecting the Power 25
- 2-6 Configuring RIC-E1 26
- Chapter 3 27
- Operation 27
- 3.2 Operating Instructions 28
- Chapter 4 29
- Troubleshooting and 29
- Diagnostics 29
- 4.2 Troubleshooting 30
- Chapter 5 31
- RIC-E1/R Card 31
- 5-2 ASM-MN-214 Card Cage 32
- 5.2 Power Supply 33
- 5.3 RIC-E1/R Front Panel 34
- CHASS-GND 36
- TX&RX CODE 36
- TIMING SEL 36
- Warning 38
- Appendix A 39
- Interface Connector Wiring 39
- [Function] 40
- [Signal 40
- Timing] 40
- A.3 Line Interface Connector 41
- Appendix B 43
- IR-ETH Interface Module 43
- 10BA SE-T 43
- B.2 Technical Specifications 45
- Setting the DIP Switch 46
- LED Indicators 46
- Connecting the LAN 47
- C.1 IR-ETH/QN Options 49
- C.2 Technical Specifications 51
- Setting the DIP Switches 52
- Appendix D 55
- IR-IP Interface Module 55
- D.2 Technical Specifications 56
- D.3 Physical Description 56
- RIC-E1/IP 57
- IR-IP LEDs 58
- IR-IP Controls 58
- Rescue Configuration 61
- Connecting the Telnet Host 62
- What to Do If 64
- D.6 IR-IP Management Utility 65
- D.7 Quick Setup Menu 66
- LAN IP Address 67
- LAN IP Mask 67
- WAN IP Address 67
- WAN IP Mask 67
- Default Gateway 67
- RIC-E1 with IR-IP 68
- DHCP Server 68
- LAN IP Address: 192.168.1.2 68
- Mask: 255.255.255.248 68
- IP Network 68
- D.8 Management Access Menu 69
- D.9 Advanced Setup Menu 70
- Interface Parameters Menu 71
- D-18 Advanced Setup Menu 72
- Protocol Field Compression 73
- Authentication Protocol 73
- Multicast IP Menu 74
- Multicast Forwarding 75
- D.10 Device Control Menu 76
- New Software Download Menu 77
- Viewing Error Log Screen 77
- Erasing Configuration 78
- Resets Menu 78
- D.11 View Menu 79
- ARP Tables 80
- Statistics Screen 81
- Using the Ping Function 83
- D.14 Erasing IR-IP Software 84
- Erasing Application Software 85
- Downloading New Software 85
- E.1 Introduction 87
- EXT INT/LBT 88
- INT/LBT Clock Mode 89
- Customer Response Form 91
- Error Report 92
Produits connexes et manuels pour Mise en réseau RAD Data comm E1 Interface Converter RIC-E1
Mise en réseau RAD Data comm 100 Spécifications
(318 pages)
(318 pages)
(106 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels