RAD Data comm ASMi-52L Spécifications Page 57
- Page / 153
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ASMi-52 Installation and Operation Manual Chapter 4 Managing ASMi-52 via a Terminal
Configuring ASMi-52 System Parameters 4-21
To access the Port Control menu:
• Path: Main Menu > Configuration > Control Port > Port Control.
The Port Control menu appears (see Figure 4-24).
ASMi-52
Port Control
1. Port Control Mode > (Terminal)
2. Terminal >
3. Dial out >
4. Save
>
ESC-prev.menu; !-main menu; &-exit; @-scroll
Figure 4-24. Port Control Menu
Configuring Port Control Mode
CONTROL port of ASMi-52 operates in one of the following modes:
• Terminal – direct connection to the control terminal (DCE mode) or to modem
(DTE mode)
• Dial-out – connection to dial-out modem for alarm reporting
• SLIP – connection to management station via Serial Line Internet Protocol.
Currently connection to ASMi-52 via SLIP is disabled.
To configure port control mode:
1. From the Port Control menu, select Port Control.
The Port Control Mode menu appears (see Figure 4-25).
ASMi-52
Port Control Mode (Terminal)
1. Terminal
2. Dial out
3. SLIP
>
ESC-prev.menu; !-main menu; &-exit; @-scroll
Figure 4-25. Port Control Mode Menu
2. From the Port Control Mode menu, select desired operation mode.
The Port Control menu appears.
3. From the Port Control menu, select Save to save the change.
Configuring User Name, Password, Pop-up Alarms and Security
Timeout
User name, password, pop-up alarms and security timeout are configured via
Terminal menu.
Note
- /4-Wire SHDSL Modem 1
- ASMi-52 3
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Warning 9
- Quick Start Guide 11
- Configuring the Master Clock 12
- Configuring the T1 Interface 13
- 4 Configuring ASMi-52 14
- Contents 15
- Table of Contents 16
- Chapter 1 17
- Introduction 17
- Applications 18
- Features 18
- Line Interface 19
- DTE Interface 19
- 1-4 Overview 20
- Management 21
- 1.2 Physical Description 22
- 1.3 Functional Description 23
- 1.4 Technical Specifications 24
- Chapter 2 27
- Installation and Setup 27
- 2.2 Package Contents 28
- 2.3 Installation and Setup 28
- Connecting the Interfaces 29
- Connecting the Power 30
- Chapter 3 31
- Operation 31
- 3.2 Operating ASMi-52 32
- 3.3 Default Settings 33
- 3-4 Default Settings 34
- Default Settings 3-5 35
- 3-6 Default Settings 36
- Chapter 4 37
- Managing ASMi-52 via a 37
- Terminal 37
- Preparing the Terminal 38
- Data Terminal Ready (DTR) 38
- Initiating a Control Session 38
- Choosing Options 40
- Correcting Entries 40
- Navigating Data Forms 40
- Logging Out 41
- ConfiguRAD 43
- Entering Device Information 46
- Configuring the LAN Port 51
- Filling out the Bridge Table 52
- Configuring Aging Timeout 53
- Setting the LAN Rate 53
- Configuring Autonegotiation 54
- Configuring Fault Indication 55
- Selecting the CTS State 56
- Selecting the DSR State 56
- Timeout 57
- Configuring the Snext Margin 62
- Configuring the Line Probing 64
- Configuring the Data Rate 66
- Configuring the E1 Interface 67
- Selecting E1 Framing Mode 68
- Defining Idle Code 69
- Mapping E1 Timeslots 70
- Displaying the System Status 74
- Displaying the Port Status 74
- 4.10 Resetting ASMi-52 79
- Resetting the ASMi-52 Modem 80
- Resetting the SHDSL Repeater 80
- 5.1 Overview 83
- Setting the ASMi-52 System 84
- Setting the Line Interface 85
- Setting the E1 port 86
- Chapter 6 87
- Troubleshooting and 87
- Diagnostics 87
- Displaying All Alarms 88
- Displaying System Alarms 89
- Displaying Port Alarms 90
- Error Detection 6-5 91
- 6-6 Error Detection 92
- Error Detection 6-7 93
- Table 6-2. ASMi-52 Events 94
- Clearing the E1 Statistics 102
- Running Loopback Tests 102
- Running the Remote Loopback 104
- 6.5 Technical Support 106
- Appendix A 107
- Interface Connector 107
- Specifications 107
- Ethernet Connector 109
- A.2 CONTROL Connector 110
- A.3 Alarm Relay Connector 111
- A-6 Alarm Relay Connector 112
- Appendix B 113
- IR-IP Interface Module 113
- B.1 Introduction 114
- B.2 Technical Specifications 115
- B.3 Physical Description 116
- IR-IP LEDs 117
- Normal Indications 117
- Connecting the Telnet Host 120
- What to Do If 122
- General Operating Procedures 123
- B.7 Quick Setup Guide 124
- ASMi-52 with IR-IP 125
- LAN IP Address: 192.168.1.2 126
- Mask: 255.255.255.248 126
- DHCP Server 126
- IP Network 126
- Defining a Telnet Password 127
- B.9 Advanced Setup 128
- Advanced Setup B-17 129
- Frame Relay Protocol 130
- PPP Protocol Menu 131
- B-20 Advanced Setup 132
- Downloading New Software 133
- Viewing the Error Log 134
- Erasing Configuration 134
- Resetting IR-IP 135
- Viewing the ARP Tables 137
- Using the Ping Function 140
- B.14 Erasing IR-IP Software 141
- Main menu 144
- Customer Response Form 148
- Error Report 150
Produits connexes et manuels pour Mise en réseau RAD Data comm ASMi-52L
(106 pages)
Mise en réseau RAD Data comm T1 Spécifications
(158 pages)
(158 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels