RAD Data comm ASMi-52L Spécifications Page 103
- Page / 153
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ASMi-52 Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics
Performing the Diagnostic Tests 6-17
Local
DTE
Data
Local ASMi-52
Data
Clock
Clock
Line
Interface
Glue
Logic
Transmit
Receive
Figure 6-19. Local Loopback
To run the local loopback:
1. From the Main menu, select Diagnostics.
The Diagnostics menu is displayed (see Figure 6-20).
2. From the Diagnostics menu, select:
Local Test to run the LLB on the local ASMi-52
Remote Test to run the LLB on the remote ASMi-52.
The Local/Remote Test menu appears (see Figure 6-21).
3. Select LLB.
The LLB value in parenthesis changes to ON. Also, an additional
parameter, Loop Timeout, is displayed for the local ASMi-52.
4. Select Loop Timeout, if you want to set loopback timeout (in minutes).
The Loop Timeout value changes.
Avoid setting timeout to 0 as local control is lost during LLB. 0=Forever
5. Once you selected the loopback timeout, select Save to activate the LLB.
The LLB is initiated. The TST indicator lights up and the ASMi-52 units lose
synchronization.
ASMi-52
Diagnostics
1. Local Test >
2. Remote Test >
3. Repeater Test >
>
ESC-previous menu ; !–main menu ; &–exit terminal
Figure 6-20. Diagnostics Menu
Note
- /4-Wire SHDSL Modem 1
- ASMi-52 3
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Warning 9
- Quick Start Guide 11
- Configuring the Master Clock 12
- Configuring the T1 Interface 13
- 4 Configuring ASMi-52 14
- Contents 15
- Table of Contents 16
- Chapter 1 17
- Introduction 17
- Applications 18
- Features 18
- Line Interface 19
- DTE Interface 19
- 1-4 Overview 20
- Management 21
- 1.2 Physical Description 22
- 1.3 Functional Description 23
- 1.4 Technical Specifications 24
- Chapter 2 27
- Installation and Setup 27
- 2.2 Package Contents 28
- 2.3 Installation and Setup 28
- Connecting the Interfaces 29
- Connecting the Power 30
- Chapter 3 31
- Operation 31
- 3.2 Operating ASMi-52 32
- 3.3 Default Settings 33
- 3-4 Default Settings 34
- Default Settings 3-5 35
- 3-6 Default Settings 36
- Chapter 4 37
- Managing ASMi-52 via a 37
- Terminal 37
- Preparing the Terminal 38
- Data Terminal Ready (DTR) 38
- Initiating a Control Session 38
- Choosing Options 40
- Correcting Entries 40
- Navigating Data Forms 40
- Logging Out 41
- ConfiguRAD 43
- Entering Device Information 46
- Configuring the LAN Port 51
- Filling out the Bridge Table 52
- Configuring Aging Timeout 53
- Setting the LAN Rate 53
- Configuring Autonegotiation 54
- Configuring Fault Indication 55
- Selecting the CTS State 56
- Selecting the DSR State 56
- Timeout 57
- Configuring the Snext Margin 62
- Configuring the Line Probing 64
- Configuring the Data Rate 66
- Configuring the E1 Interface 67
- Selecting E1 Framing Mode 68
- Defining Idle Code 69
- Mapping E1 Timeslots 70
- Displaying the System Status 74
- Displaying the Port Status 74
- 4.10 Resetting ASMi-52 79
- Resetting the ASMi-52 Modem 80
- Resetting the SHDSL Repeater 80
- 5.1 Overview 83
- Setting the ASMi-52 System 84
- Setting the Line Interface 85
- Setting the E1 port 86
- Chapter 6 87
- Troubleshooting and 87
- Diagnostics 87
- Displaying All Alarms 88
- Displaying System Alarms 89
- Displaying Port Alarms 90
- Error Detection 6-5 91
- 6-6 Error Detection 92
- Error Detection 6-7 93
- Table 6-2. ASMi-52 Events 94
- Clearing the E1 Statistics 102
- Running Loopback Tests 102
- Running the Remote Loopback 104
- 6.5 Technical Support 106
- Appendix A 107
- Interface Connector 107
- Specifications 107
- Ethernet Connector 109
- A.2 CONTROL Connector 110
- A.3 Alarm Relay Connector 111
- A-6 Alarm Relay Connector 112
- Appendix B 113
- IR-IP Interface Module 113
- B.1 Introduction 114
- B.2 Technical Specifications 115
- B.3 Physical Description 116
- IR-IP LEDs 117
- Normal Indications 117
- Connecting the Telnet Host 120
- What to Do If 122
- General Operating Procedures 123
- B.7 Quick Setup Guide 124
- ASMi-52 with IR-IP 125
- LAN IP Address: 192.168.1.2 126
- Mask: 255.255.255.248 126
- DHCP Server 126
- IP Network 126
- Defining a Telnet Password 127
- B.9 Advanced Setup 128
- Advanced Setup B-17 129
- Frame Relay Protocol 130
- PPP Protocol Menu 131
- B-20 Advanced Setup 132
- Downloading New Software 133
- Viewing the Error Log 134
- Erasing Configuration 134
- Resetting IR-IP 135
- Viewing the ARP Tables 137
- Using the Ping Function 140
- B.14 Erasing IR-IP Software 141
- Main menu 144
- Customer Response Form 148
- Error Report 150
Produits connexes et manuels pour Mise en réseau RAD Data comm ASMi-52L
(106 pages)
Mise en réseau RAD Data comm T1 Spécifications
(158 pages)
(158 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels