RAD Data comm LA-210 Manuel d'utilisateur Page 62
- Page / 158
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3 Configuration Management User’s Manual
3-32 Setting the Operational Parameters RV-EMS/NGN LA-210
Parameter Possible Values / Remarks
OAM Mode
Determines the OAM behavior.
Disabled: No CC performed
Initiate: The unit will initiate and respond to OAM messages
React: The unit will respond to OAM messages, but not initiate them.
Default: Disabled
Continuity Verification
Mode
Determines the CC behavior. LB Based is used only for RAD proprietary.
LB Based
CC Based
Default: Disabled
Note: This parameter is available in Initiate/React OAM mode
.
OAM Destination
Address Type
Unicast
Multicast
Default: Unicast
Note: This parameter is available in Initiate OAM mode
.
OAM Destination MAC
Address
Determines the MAC address sent in OAM messages, configurable only for
Unicast MAC Address.
Default: 01-20-d2-00-01-00 + MD Level in RAD Proprietary, Standard OAM MAC
Address + MD Level in Standard.
Default CC Priority The priority CFM messages will be sent if no service is defined on the flow. If a
service is defined, the CC will be performed at the highest priority service on the
flow.
Note: This parameter is available in Initiate OAM mode
.
³ To edit a flow:
1. In the OAM List screen, select the desired flow and click <Change>.
The Change Flow dialog appears. The Change Flow dialog is identical with
the Add Flow dialog (
Figure
3-23
).
2. Configure the parameters as outlined in
Table
3-13
.
3. Click <Set>.
The flow has been modified.
³ To edit a service:
1. Before you can edit a service, set the OAM mode to React or Initiate,
otherwise the service parameters will be read only.
2. Select the desired service.
The associated service parameters appear.
- RADview-EMS/NGN 1
- Contents 3
- RV-EMS/NGN LA-210 iii 5
- Chapter 1 7
- Introduction 7
- System Level Operations 9
- Chapter 2 13
- Installation and Operation 13
- Management 14
- 2-1. Host Menu (LA-210) 16
- 2-4. Host Menu (LA-210) 18
- Stations 19
- LA-210 View Window 21
- Toolbar 22
- Status Bar 22
- LA-210 System 23
- RADview LA-210 Menu Maps 24
- Selecting the System 26
- Selecting Ports 26
- Front Panel Connectors 27
- Indicators and LEDs 27
- Chapter 3 31
- Configuration 31
- Setting System Date and Time 34
- 3-3. SHDSL Port Parameters 38
- Configuring SHDSL Lines 41
- 3-10. PCS Parameters Screen 43
- 3-6. PCS Parameters 43
- Configuring the Flows 44
- Defining CoS Profiles 46
- 3-13. CoS Profiles List 47
- 3-14. Adding CoS Profile 47
- 3-8. CoS Profile Parameters 48
- Defining Marking Profiles 49
- 3-19. Flows Screen 54
- 3-11. Flows Parameters 54
- 3-20. Adding a Flow 56
- 3-12. Flow Parameters 56
- Configuring OAM (CFM) 60
- 3-23. Adding a Flow (OAM) 61
- 3-13. (OAM) Flow Parameters 61
- 3-14. Change Service Dialog 64
- • In the Bridge port list ( 67
- ), click Refresh 67
- Configuring MAC Tables 69
- Configuring QoS 70
- 3-31. QoS Classification 71
- 3-32. QoS Mapping 71
- 3-33. Fault Propagation 72
- 3.3 Additional Tasks 73
- Chapter 4 75
- Configuring a Flow-Based 75
- Point-To-Point Application 75
- 4.2 Configuration Sequence 76
- Configuring ETX-202 Server 79
- Configuring ETX-202 Client 80
- 4.5 Configuring LA-210 83
- 4-10. System Parameters 84
- 4-11. Flow Dialog 85
- 4-12. Adding a Flow Dialog 86
- 4-15. CoS Profiles 88
- 4-16. Adding CoS Profiles 89
- 4-17. Flow Definition 90
- 4-18. Ingress BW Profiles 91
- Configuring the DSLAM 95
- Using the VLC Media Player 96
- Ping Tests 97
- Policer Testing 98
- Priority Testing 105
- Chapter 5 111
- Performance Management 111
- Polling the Agent 112
- Viewing Flow Statistics 113
- Viewing Service Statistics 117
- 5-4. Service Statistics 118
- 5-5. Service Statistics 120
- Clearing All Statistics 121
- Viewing Line Statistics 121
- Viewing PCS Statistics 124
- Viewing ATM Statistics 124
- The ATM statistics appear 125
- Viewing VCC Statistics 126
- Viewing Rx Frame Types 127
- Viewing Tx Frame Types 128
- Viewing Errors 129
- 5-15. Errors Dialog Box 130
- Viewing Running Counters 132
- Viewing Current Frames 133
- Viewing Current Delays 134
- Viewing Interval Frames 135
- Viewing Interval Delays 136
- Chapter 6 139
- Security Management 139
- Monitor 140
- Technician 141
- Operator 141
- Administrator 141
- 6.3 Configuring SNMP 142
- Chapter 7 147
- Fault Management 147
- ³ To add a configuration: 149
- Viewing the History Log 152
- Clearing the History Log 155
- RV-EMS/NGN LA-210 Ver. 1.2 158
Produits connexes et manuels pour Mise en réseau RAD Data comm LA-210
Mise en réseau RAD Data comm E1 Spécifications
(118 pages)
(118 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.164 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels