RAD Data comm FCD-X21 Manuel d'installation Page 207
- Page / 224
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Operation Manual Appendix D Command Language
FCD-E1 Supervisory Terminal Commands D-45
Table D-14. FCD-E1 Default Configuration Used with Supervision Terminal (Cont.)
Type Parameter Designation Default Value
Data Channels MULTIPLIER
SPEED
FIFO SIZE
CLK_MODE
CTS
MAP_MODE
START_TS
TS_TYPE
Timeslot Map Type (USER
mode only)
ETHERNET MODE
BRIDGING
64
NC
AUTO
DCE
ON
USER
N/A
N/A
NC
HALF
FILTER
SP (Supervisory Port) SPEED
DATA
PARITY
INTERFACE
CTS
DCD_DEL
DSR
POP_ALM
PWD
LOG_OFF
AUXILIARY_DEVICE
AUTO
8
NO
DCE
=RTS
0_MS
ON
NO
NO
NO
TERMINAL
DP (Dial-out Port) SPEED
DATA
PARITY
CALL_OUT_MODE
9600 bps
8
NO
NONE
Download DNLOAD MODE NONE
BERT PATTERN
ERROR_INJECTION_RATE
RX_INBAND
2E3-1
NO ERR
DISABLE
LOOP
Purpose
Activate the specified user-initiated test or loopback.
A remote loopback cannot be activated when a local loopback is already
connected, and vice versa. In such case, you will see ERROR 051 (illegal port loop
configuration).
Syntax
LOOP {‘loopback’}
Note
- E1 or Fractional E1 1
- Access Unit 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- Cable Connections 12
- Configuration Procedure 13
- 4 FCD-E1 14
- Contents 15
- FCD-E1 iii 17
- 1.1 Overview 19
- Main Link Interfaces 20
- Optical Main Link 21
- Sublink Interface 22
- Data Channel Interfaces 22
- Ethernet Interfaces 22
- Timeslot Handling 23
- Management 25
- Statistics Collection 26
- Diagnostics 26
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Transmit Path 29
- Receive Path 30
- Bypass Relays 31
- Main Link Timing Application 33
- Sublink Timing Application 34
- Customer Premises 35
- System Management Method 36
- CONTROL DCE Port 37
- Clear to Send (CTS) 39
- Data Carrier Detect (DCD) 39
- Data Set Ready (DSR) 39
- AUTOBAUD Function 40
- SNMP Management Capabilities 41
- Alarm Relay 44
- 1.4 Technical Specifications 45
- 2.1 Introduction 51
- 2.3 Package Contents 52
- 2.4 Equipment Needed 52
- Warning 53
- Cover Screw 55
- (4 Places) 55
- JP10, JP11 57
- CLK POLARITY 57
- 2.6 Connecting the Cables 64
- Ethernet Data Channel 67
- Connecting the Alarm Relay 68
- AC Power Connection 69
- DC Power Connection 69
- 3.1 Turning FCD-E1 On 71
- 3.2 Controls and Indicators 71
- Status Messages 74
- Diagnostics Functions 74
- Test Functions 74
- Additional Function of Enter 75
- Fault Indications 75
- 3.3 Default Settings 76
- Multidrop Connections 78
- Connection of Dial-Up Modem 79
- 3.6 Turning FCD-E1 Off 82
- 4.1 Configuration Sequence 83
- 4.2 Introduction 84
- FCD-E1 Introduction 4-3 85
- Preparation of FCD-E1 87
- Initial Configuration 87
- Configuration of Terminals 88
- SNMP Agent Configuration 89
- Explicit Mode Command Syntax 97
- Command Options 97
- Command Fields 99
- Ending a Session 99
- Using the Mnemonic Mode 100
- FCD> 103
- TERMINAL ON LINE 103
- FCD-E1 104
- Ending a Control Session 105
- Configuring Typical 107
- Applications 107
- Chapter 5 107
- 5.3 Configuration Example 108
- Configure System Timing 112
- 6.1 Monitoring Performance 113
- 6.2 Detecting Errors 116
- Front-Panel LEDs 117
- 6.3 Handling Alarms 119
- Handling Alarms 6-9 121
- 6-10 Handling Alarms 122
- Handling Alarms 6-11 123
- 6-12 Handling Alarms 124
- Handling Alarms 6-13 125
- From the Control Terminal 126
- From the LCD 126
- 6.4 Troubleshooting 127
- 6.5 Testing FCD-E1 128
- Testing FCD-E1 6-17 129
- 6-18 Testing FCD-E1 130
- LOCAL FCD-E1 131
- REMOTE FCD-E1 131
- 6-20 Testing FCD-E1 132
- Testing FCD-E1 6-21 133
- BER Testing (LP BERT CH) 134
- 6.7 Technical Support 135
- 6-24 Technical Support 136
- A.1 E1 Port Connectors 137
- A.2 Data Channel Connector 138
- DCE Mode 139
- DTE1 Mode 139
- DTE2 Mode 140
- CONTROL DCE Connector 150
- CONTROL DTE Connector 150
- B.1 Scope 151
- B.2 SNMP Environment 151
- SNMP Operations 152
- MIB Structure 152
- SNMP Communities 153
- B.3 IP Environment 154
- Net and Subnet Masks 155
- B.5 SNMP Traps 158
- C.1 Scope 159
- C.2 E1 Environment 159
- TimeSlot 0 160
- Multiframes 160
- E1 (CEPT) Line Signal 161
- C-4 E1 Environment FCD-E1 162
- D.1 General 163
- D.2 Front Panel Parameters 163
- CLR ALM 175
- Purpose 176
- DEF AGENT 177
- DEF NAME 189
- DEF NODE 189
- DEF ROUTE 190
- DEF PWD 190
- DSP AGENT 195
- DSP ALM 195
- DSP HDR TST 198
- EXIT<Enter> 205
- F<Enter> 205
- CLEAR SCREEN =hhhhhhhh 205
- CURSOR HOME =hhhhhhhh 205
- CURSOR RIGHT =hhhhhhhh 205
- PASSWORD 209
- MINUTE = 02 210
- SECOND = 05 210
- E.1 Introduction 211
- E.2 IR-ETH Interface Option 212
- E.3 Technical Specifications 213
- LED Indicators 214
- F.1 Introduction 215
- F.3 Technical Specifications 216
- Connecting to LAN 217
- Customer Response Form 219
- Error Report 221
Produits connexes et manuels pour Mise en réseau RAD Data comm FCD-X21
Mise en réseau RAD Data comm E1 Spécifications
(118 pages)
(118 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels