RAD Data comm IPmux-24 Spécifications Page 77
- Page / 190
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IPmux-24 Ver. 1.5 Configuring IPmux-24 for Management 4-1
Chapter 4
Configuration
This chapter illustrates the configuration IPmux-24 screens and explains their
parameters.
Menu trees of the IPmux-24 management software are shown in
Chapter 3
.
4.1 Configuring IPmux-24 for Management
Usually, initial configuration of the management parameters is performed via
ASCII terminal. Once the IPmux-24 host IP parameters are set, it is possible to
access it via Telnet, Web terminal or RADview for operation configuration.
Perform the following steps in order to configure IPmux-24 for management:
³ To configure IPmux-24 for management:
1. Connect an ASCII terminal to the RS-232 control port of IPmux-24.
2. Log in as Superuser (su).
3. Enable or disable the IPmux-24 DHCP client.
4. Assign an IP address to IPmux-24.
5. Assign a subnet mask and a default gateway.
6. Configure the SNMP communities.
7. Set a manager IP address.
Make sure that you save your settings at each configuration screen.
Configuring IP Host Parameters
IPmux-24 can be managed by a network management station, which is located on
the LAN connected to the one of the unit’s Ethernet ports. In order to establish a
proper connection, it is necessary to configure the following: host IP address,
subnet mask, default gateway, its trap, read and write communities. In addition,
you can enable or disable DHCP client of the device.
Note
- IPmux-24 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Glossary 11
- Français 15
- Declaration of Conformity 17
- Quick Start Guide 19
- Configuring the System Clock 20
- Connecting Bundle 20
- Contents 23
- IPmux-24 Ver. 1.5 iii 25
- Chapter 1 27
- Introduction 27
- E1 Interface 28
- T1 Interface 28
- Packet Networks 29
- Ethernet 29
- Payload Encapsulation 30
- HDLCoPSN 31
- Ring Topology 31
- Management 31
- Web Terminal 32
- RADview-SC/TDMoIP 32
- Environment 32
- 1.2 Physical Description 33
- 1.3 Functional Description 33
- Unframed 34
- Fractional 34
- Fractional with CAS 34
- E1/T1 Timing 35
- System Timing 35
- External Network Timing 36
- Adaptive Timing 37
- 1 Time to Live 38
- VLAN Support 39
- UDP Support 39
- Note: IEEE 802.1p&Q VLAN 40
- 1-11. SAToP Encapsulation 41
- Packet Delay Variation 42
- PDVT (Jitter) Buffer 42
- Packet Creation Time (PCT) 43
- 0.125N × 44
- Pseudowire OAM 45
- End-to-End Alarm Generation 45
- Trail-Extended Mode 45
- VLAN Traffic Behavior 46
- Double Host 47
- Security 49
- Rate Limitation 49
- Chapter 2 53
- Installation and Setup 53
- 2.4 Equipment Needed 54
- 2.5 Mounting the Unit 54
- 2.6 Installing SFP Modules 55
- 2.12 Connecting to Power 58
- Connecting AC Power 59
- Connecting DC Power 59
- Chapter 3 61
- Operation 61
- 3.3 Default Settings 62
- 3-2. Default Settings 63
- Working with Terminal 67
- Choosing Options 68
- Web Browser Requirements 69
- Working with RADview 71
- Working with SNMP 71
- Menu Maps 71
- Connection 72
- Bundle Connection 72
- Configuration 72
- 3.5 Turning IPmux-24 Off 75
- Chapter 4 77
- Configuring DHCP Client 78
- Defining Network Managers 81
- Configuring SNMPv3 82
- Enabling SNMPv3 83
- Adding SNMPv3 Users 84
- Adding Notification Entries 85
- Assigning Traps 85
- 4-10. Trap Menu 86
- Configuring Target Address 87
- Mapping SNMPv1 to SNMPv3 88
- Configuring RADIUS Client 91
- 4-2. Protection Parameters 96
- 4-20. Figure 98
- 4-21. TDM (E1) Menu 98
- 4-26. DS0 Bundle Menu 106
- 4 Configuration 109
- Configuring MAC Table 116
- Configuring the Bridge Ports 117
- Configuring L2CP Handling 119
- 4-36. Classification Menu 122
- Configuring Rate Limitation 123
- 4.3 Additional Tasks 125
- Setting the Date and Time 126
- 4-41. Date/Time Menu 127
- Chapter 6 127
- Displaying the SFP Status 128
- 4-44. Connection Screen 129
- Resetting IPmux-24 132
- Chapter 5 135
- Configuring IPmux-24 for 135
- Typical Applications 135
- IPmux-24 Ver. 1.5 136
- Configuring Bundles 139
- Connecting the Bundles 140
- Configuring the Bridge 141
- Protection 142
- Configuration Sequence 143
- Unmasking Ring Status Traps 147
- Chapter 6 149
- Diagnostics and 149
- Troubleshooting 149
- 6-1. E1/T1 Statistics 151
- 6.2 Detecting Errors 159
- Accessing Event Log 160
- Clearing Events 162
- 1. Check the E1/T1 cable 163
- 2. Check all framing-related 163
- 3. Check input signal 163
- Masking Alarm Traps 164
- 6.4 Troubleshooting 165
- 6.5 Testing IPmux-24 165
- External Loopback 166
- Internal Loopback 166
- Pinging IP Hosts 169
- Running a Trace Route 170
- 6-19. Trace route Menu 171
- 6.7 Technical Support 174
- Appendix A 175
- Connector Wiring 175
- A.2 Ethernet Connectors 176
- A.3 CONTROL Connector 177
- A.2 Alarm Relay 178
- Appendix B 179
- Boot Sequence and 179
- Downloading Software 179
- Software 180
- AC/DC Adapter 183
- (AD) Plug 183
- AC/DC Adapter (AD) Plug 184
- Customer Response Form 185
- Error Report 187
- International Headquarters 190
- North America Headquarters 190
Produits connexes et manuels pour Passerelles/contrôleurs RAD Data comm IPmux-24
(99 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels